Asterisk Install: Difference between revisions
(New page: OK, Asterisk 1.6.0 is out and I'm going to take the plunge. I am going to document my steps below. The following is based on CentOS 5.2 as been installed with the minimal components incl...) |
No edit summary |
||
| Line 11: | Line 11: | ||
I did not download and install the Libpri package as I don't have any primary rate cards installed on my system. | I did not download and install the Libpri package as I don't have any primary rate cards installed on my system. | ||
=== | === dahdi-linux === | ||
DAHDI (stands for Digium Asterisk Hardware Device Interface) is the replacement for Zaptel. As I have an [[X100P]] card installed into my system I need to install the Linux driver. If you do not have any telecommunications cards installed you will not need to install the module. | DAHDI (stands for Digium Asterisk Hardware Device Interface) is the replacement for Zaptel. As I have an [[X100P]] card installed into my system I need to install the Linux driver. If you do not have any telecommunications cards installed you will not need to install the module. | ||
<pre> | <pre> | ||
| Line 20: | Line 20: | ||
</pre> | </pre> | ||
=== | === dahdi-tools === | ||
<pre> | <pre> | ||
| Line 35: | Line 35: | ||
Once the above is done we need to edit '''/etc/dahdi/modules''' and make sure that only the required dahdi module(s) is/are loaded. | Once the above is done we need to edit '''/etc/dahdi/modules''' and make sure that only the required dahdi module(s) is/are loaded. | ||
=== | === asterisk === | ||
<pre> | <pre> | ||
tar xvzf asterisk-1.6.0.tar.gz | tar xvzf asterisk-1.6.0.tar.gz | ||
| Line 46: | Line 46: | ||
make config | make config | ||
</pre> | </pre> | ||
=== | === asterisk-addons === | ||
<pre> | <pre> | ||
tar xvzf asterisk-addons-1.6.0.tar.gz | tar xvzf asterisk-addons-1.6.0.tar.gz | ||
Revision as of 06:45, 7 October 2008
OK, Asterisk 1.6.0 is out and I'm going to take the plunge. I am going to document my steps below. The following is based on CentOS 5.2 as been installed with the minimal components including the development tools.
The First thing I did was to download the the Asterisk source files.
Asterisk 1.6.0 DAHDI Linux 2.0.0 DAHDI Tools 2.0.0 Addons 1.6.0
I did not download and install the Libpri package as I don't have any primary rate cards installed on my system.
dahdi-linux
DAHDI (stands for Digium Asterisk Hardware Device Interface) is the replacement for Zaptel. As I have an X100P card installed into my system I need to install the Linux driver. If you do not have any telecommunications cards installed you will not need to install the module.
tar xvzf dahdi-linux-2.0.0.tar.gz cd dahdi-linux-2.0.0 make make install
dahdi-tools
tar xvzf dahdi-tools-2.0.0.tar.gz cd dahdi-tools-2.0.0 ./configure make menuselect make make install make config
Once the above is done we need to edit /etc/dahdi/modules and make sure that only the required dahdi module(s) is/are loaded.
asterisk
tar xvzf asterisk-1.6.0.tar.gz cd asterisk-1.6.0 ./configure make menuselect make make install make samples make config
asterisk-addons
tar xvzf asterisk-addons-1.6.0.tar.gz cd asterisk-addons-1.6.0 yum install mysql ./configure make menuselect make make install
